njret.blogg.se - How to get sentry safe open without key

How to get sentry safe open without key full#
How to get sentry safe open without key code#

The battery icon ( ) will light when the batteries need to be replaced. Additional pressure to the left corner of the door may be required before the handle can be returned to the horizontal position. NOTE: If your unit is equipped with a water resistant gasket. For greatest security, depress the key lock (if equipped) with your finger. When the unlocked padlock icon ( ) appears, you have four seconds to turn the handle down to open.Ĭlose the door and return the handle to the

How to get sentry safe open without key code#

Try this several times before proceeding to the next step.Įnter the 5-digit factory code, a pre-programmed manager code, or a pre-programmed user code (programming instructions to follow), then press the Prog/Enter key. When the unlocked padlock icon ( ) appears, you have four seconds to turn the handle down to open.

Enter the factory code (printed on the fi rst page of this guide), then press the Prog/Enter key.

Turn the key (if your safe is equipped with a key lock) to the right so that the lock cylinder pops out.

Comes ON when the batteries need to be replaced.

Comes ON in the Programming mode and remains lit until you have finished entering a 5-digit code.ġ.

Comes ON after you enter a valid code and remains lit during the 4-second period in which the safe can be opened.

Lights after three consecutive invalid codes are input (2-minute delay mode).

You have let 5 seconds or more elapse between key presses.

You have entered an invalid code or user pin.

You have pressed Program key out of sequence.

Red (Error) LED + three beeps indicates one of the following:

Your electronic-lock safe communicates by means of several audio/visual signals. NOTE: If your safe does not appear to be working, please check batteries before calling Sentry Customer Care. Enter the 5-digit user pin of your choice.Enter the 5-digit user code of your choice.Press the Prog key, then enter the 5-digit factory code.If you wish to give someone else temporary access to the safe, you can program a 5-digit user pin that can later be erased. If you prefer to employ your own code, you can program the safe to open using a 5-digit user code of your choice. (Found on the fi rst page of this guide) You can always open the safe by entering the pre-set 5-digit factory code. There are 3 possible ways to unlock and access the safe: NOTE: If your unit is equipped with a water resistant gasket additional pressure to the left corner of the door may be required before the handle can be returned to the horizontal position. When the green LED lights you have 4 seconds to turn the handle and open the safe.Ĭlose the door and return the handle to the horizontal position. Try this several times before proceeding to the next step.Įnter the 5-digit factory code, a pre-programmed user code, or a pre-programmed user pin (programming instructions to follow). When the green light appears, you have four seconds to turn the handle down to open. Enter the factory code (printed on the fi rst page of this guide).Turn the key (if your safe is equipped with a key lock) to the right so the lock cylinder pops out.NOTE: The yellow LED will light when the batteries need to be replaced. Replace the electronic lock case and turn to the left (to 12 o’clock) to reassemble.

Insert 4 new AA batteries (not included) to power this lock.

Turn the electronic lock case to the right (clockwise), from 12 o’clock to 2 o’clock, and remove.

Remove and discard the screw (if equipped) at the base of the lock case.

Opening your safe for the first time (keep door open during setup): The handle should be all of the way UP, in the horizontal position before attempting to open safe. Gain entry with the basic electronic lock Stop the FIRST time you reach the last number of your combination.Ģ. Stop the SECOND time you reach the combination’s third number. Stop the THIRD time you reach the second number of your combination. Then stop at the first number of your combination. Make sure ZERO passes the pointer at least FOUR times. (Make sure the door handle is in the horizontal position.)

How to get sentry safe open without key full#

With the door closed, depress the key lock (if equipped) with your finger, or spin the combination dial one full turn. Stop the FIRST time the pointer reaches the third number of your combination. Stop the SECOND time you reach the second number of your combination.

Make sure ZERO passes the pointer at least THREE times. NOTE: The safe will lock if key lock cylinder is pressed in with or without key. Before dialing your combination, simply insert the key (if equipped) in the lock and turn until the plunger pops out.